Available only at Lowe's
Product Features & Benefits
- Spray settings include: Full Body spray, Fast Massage spray, Full Spray with Massage
- Soft, rubber Touch-Clean® spray holes allow you to easily wipe away calcium and lime build-up from the spray face of your shower head and hand shower with the touch of a finger
- For use with PTR188700 Series rough valve (included)
- Touch Clean
- Water Efficient Product meeting CALGreen standards
- WaterSense Labeled
- ADA Compliant
- Handle(s): Single Handle Lever
- With Side Sprayer: F
- With Soap/Lotion Dispenser: F
- Flow Rate: 2.00 gpm @ 80 psi, 7.6 L/min @ 550 kPa
- Valve Type: Single-function pressure balance cartridge
- Installation: N/A
- Spout Total Height: 6
Rated 5 out of 5 by NewCustomer from Great product and excellent service I purchased a shower set but the escutheon screws were missing. I contacted customer service and received the missing parts within a few days NO QUESTIIONS ASKED. unfortunately the screws were short because the way the plumber installed the mixer. I contacted customer service again and asked if they can send me longer screws with the same color as the faucet. Once again I received the parts within few days and again NO questions asked.
Date published: 2017-11-16
Instructions say "Caution excessive heat may damage valve unit". How do I solder copper pipe into the valve unit without heating it too much? If removing the valve body from the brass fittings is required, how do I do that without causing damage?
Hello James66, Thank you for your question. We do not recommend soldering pipes directly to the valve of the Peerless Tub and Shower P18437-BN faucet model. However, you can solder a threaded adapter onto the copper pipe, then connect that to the valve. There are not brass parts required to be removed from the valve for installation. https://media.peerlessfaucet.com/MandI/90547%20Rev%20B.pdf Best regards, Tanya
Date published: 2018-02-27
Does model come in a shower only version? I want it for my new shower, I don't need the tub spout.
Hello Yooper, Thank you for your question. The Peerless Tub and Shower P18437-BN is not manufactured as a shower only unit. Best regards, Tanya
Date published: 2018-02-19
To install the spout diverter with iron pipe what do you need to do? There are no instructions. Other spouts you remove the plastic insert. I could not remove mine. In fact, it broke while trying to remove it.
We installed a 1/2 inch iron pipe nipple that was 4 inches from the tub surround. It only screws in maybe an inch. Then gets difficult to screw in. I assume the unthreaded part of the nipple prevents further installation. The directions do not work. The plastic is also not very secure.
Date published: 2018-02-07
Hot water pressure isn't working
Hello Nate, Thank you for your question. You may have some debris trapped in the valve body or cartridge assembly that is blocking the hot water flow. You may need to clean out the cartridge assembly and flush out the valve body. First turn off the water supply to the faucet. Remove the handle assembly, unscrew the bonnet ring and remove the cartridge assembly and all seals. Rinse and clean the cartridge out thoroughly. Turn both the hot and cold water back on for 10 to 15 seconds to flush out the valve body. After the allotted time, turn the water off and reinstall all of the components. Make sure that there is no debris on the cartridge assembly and seals. Best regards, Tanya
Date published: 2018-02-05
The directions state that a 3 7/8 - 4" pipe should extend from the finished wall. This is fine if you are using threaded pipe but if you are using just 1/2" copper the tub spout will only go 3 1/4" leaving it 3/4" from the wall. Please advise.
ShermanJoe, Thank you for your question. For a slip-on installation, we recommend that the pipe extend 1-1/2" to 2-3/4” from the finished wall. Best regards, Jon
Date published: 2018-02-23
how can i increase the water flow
Thank you for your question, Morris. The maximum flow rate of the shower head is 2.0 GPM at 60 PSI. If you are experiencing reduced flow, please try removing it from the arm and checking for debris. The tub spout should run at about 5 GPM at 60 PSI. Best regards, Jon
Date published: 2017-12-08
how can i connect the tub spout? i have cpvc piping .
cpvc, Thank you for your question. For models with tub spouts, the piping between valve body and tub spout must be a minimum of 1/2" copper pipe or 1/2" iron pipe in a straight drop no less than 8", but no more than 18" (457 mm) long with only one iron pipe or copper 90° elbow to the tub spout nipple. Other forms of piping can result in back pressure that causes water to go to the shower head when the water is not being diverted. Please refer to page 3 of the installation instructions as well as the instructions on the bag that the tub spout came in for more information. https://media.peerlessfaucet.com/MandI/90547%20Rev%20B.pdf Best regards, Jon
Date published: 2017-12-07
It won't let the hot water get as hot as it should.
Jgee, I'm sorry for any inconvenience. Please refer to page 5 of the Installation Instructions (link below) for help adjusting the Rotational Limit Stop. This will allow for more hot water. https://media.peerlessfaucet.com/MandI/90547%20Rev%20B.pdf Best regards, Jon
Date published: 2017-11-29
1The manufacturer's list price (U.S. dollars) is shown for comparison only. The actual retail price may be different from the price shown.